Practical woodworking for apartments, rentals, and small spaces. About
Beginner Woodworking

Plywood Grades Explained for Small Projects

A C face on sheathing plywood can have open 1-inch knotholes; a C face on birch plywood cannot. Plywood grades explained from the two US standards.

Stacked plywood sheets and timber in a warehouse
Plywood grade letters mean different things depending on which grading system the sheet uses.
This article may contain affiliate links. We may earn a commission at no extra cost to you.

Short answer: plywood grades explained in one line: the letter on the sheet only describes the surface veneer, and the same letter means different things depending on which standard the panel follows. Construction plywood graded under the US standard PS 1 uses two letters for face and back (A-C, B-C, C-D). Hardwood plywood graded under ANSI/HPVA HP-1 uses a letter for the face and a number for the back (A-1, B-2, C-3). A "C" face on PS 1 sheathing may have open knotholes about the width of a quarter; a "C" face on HP-1 birch plywood must be a sound face with no open defects.

For a small project, that difference decides whether you are buying a painted bookshelf face or a sheet that needs filling first. Below is what each grade actually permits, read from the two standards themselves, and which grade a small build really needs.

Which grading system is your plywood using?

Look at the stamp or label before you look at the letters.

  • PS 1 (structural or "construction" plywood). Voluntary Product Standard PS 1-19, published through NIST, requires the panel mark to include a bond classification ("Exterior" or "Exposure 1"), the grade name or face and back veneer grades (or an inspection agency mark), and the symbol "PS 1-19". Grades are written as two letters, face first.
  • HP-1 (hardwood and decorative plywood). ANSI/HPVA HP-1-2024, from the Decorative Hardwoods Association, lists face grades AA, A, B, C, D and E and back grades 1, 2, 3 and 4. Industrial panels 1/2 inch or thicker are to be marked with the standard's name, the producer, and the species and grade of the face and back.

If you see two letters and "PS 1", read the PS 1 section below. If you see a wood species with a letter and a number, read the HP-1 section.

Plywood grades explained: what each PS 1 letter allows

House framing sheathed with plywood panels
Construction grades allow defects that matter on furniture but not on a wall.

PS 1 grades the veneers of a 4 by 8 foot panel, and its section 5.4 says the limits are "proportionate for other sizes." Here is what each face grade permits, in the standard's own terms. To make the sizes easier to picture, a US quarter is 0.955 inch across and a half dollar is 1.205 inch, according to the US Mint's coin specifications.

PS 1 grade What the standard allows (4x8 panel) Rough size picture
N "intended for natural finish": all heartwood or all sapwood, no knots or knotholes, well matched; up to 6 wood repairs Clear face, very few patches
A "suitable for painting": no knots or open defects, but repairs (patches) "limited to a total of 18 in number" Smooth, but may show up to 18 football-shaped patches
B Solid surface; sound, tight knots up to 1 inch across the grain; splits no wider than 1/32 inch; repairs allowed Knots up to about a quarter's width
C plugged Openings no larger than 1/4 by 1/2 inch; sound, tight knots up to 1-1/2 inch Small filled or plugged holes
C Tight knots up to 1-1/2 inch; any number of knotholes up to 1 inch, with an occasional one up to 1-1/2 inch; splits up to 1/2 inch wide (measured 8 inches from the end) over up to half the panel length Open holes up to about a quarter, occasionally a half dollar
D Tight knots and knotholes up to 2-1/2 inch, an occasional one up to 3 inches; splits up to 1 inch wide at the measuring point Open holes up to 2-1/2 inch, more than two quarters side by side

Two things in that table surprise most beginners:

  • A does not mean patch-free. PS 1 describes Grade A as "suitable for painting" and permits up to 18 repairs. Only Grade N is written for a natural finish. If you plan to stain the face, an A-grade sheathing panel may show its patches through the finish.
  • C and D faces have open holes. For a C face, PS 1 says: "Any number of knotholes up to 25.4 mm (1 in) shall be permitted." That is fine for a shop jig or a hidden back, not for a surface you will see.

Because the limits are proportionate, a 2 by 4 foot piece (a quarter of a sheet) works out to about 4 or 5 repairs on an A face by our arithmetic, not 18. The holes and knots can still be the full size.

Exterior vs Exposure 1, and what "CDX" does not tell you

PS 1 has only two bond classifications. Exposure 1 is for panels "not permanently exposed to the weather" that resist moisture during construction. Exterior is for "repeated wetting and redrying or long-term exposure to weather." The title of the standard's table of Exterior grades says they do not permit D grade veneer, so any panel with a D face or back (such as C-D) is an Exposure 1 panel under PS 1, not an Exterior one. The trade name "CDX" does not appear in PS 1 at all; to know the bond class, read the stamp, which must state it.

Hardwood plywood: face letters and back numbers

Hardwood plywood is what you usually see sold as birch, maple, poplar or oak plywood for furniture. HP-1 judges appearance first. Here are its face grades for the species group that includes birch, maple and poplar (HP-1 Table 3.1b), plus the general grade descriptions:

HP-1 face grade Scattered sound and repaired knots (birch, maple, poplar) Other notes from the standard
AA None Smooth, tight-cut, full-length veneer; widest minimum veneer pieces (6 inches on plain-sliced faces)
A None Smooth, tight-cut; multi-piece faces book matched unless another match is specified
B Up to 4 per 4x8 panel; sound knots up to 3/8 in, repaired up to 1/8 in "pleasing matched" for color
C Up to 8 per panel; sound and repaired up to 1/2 in Unlimited color variation; "a sound face, free of open defects"
D Up to 10 per panel; repaired up to 3/4 in, sound up to 1 in Some rough grain allowed; still a sound face
E No limit on number; repaired up to 1 in, sound up to 1-1/2 in Sound face, more rough grain allowed

And the back grades (HP-1 Table 7 and section 3.4):

HP-1 back grade What the standard allows
1 Up to 16 sound tight knots, max 3/8 in; knotholes only as tiny repaired ones
2 Up to 16 sound tight knots, max 3/4 in; knotholes up to 1/2 in, all repaired
3 Knots up to 1-1/2 in; knotholes up to 1 in; some open defects
4 Knotholes up to 4 in; open splits and joints within limits

HP-1 sums it up in section 3.4: grades 1 and 2 "provide sound surfaces with all openings in the veneer repaired" (apart from tiny wormholes), while grades 3 and 4 "permit some open defects."

Same letter, different meaning

This is the comparison that most "A, B, C, D" explainers miss, because they describe one system and apply it to both:

Letter Under PS 1 (construction plywood) Under HP-1 (hardwood plywood)
A No knots, up to 18 patches; for paint No scattered sound or repaired knots (a few small pin knots allowed); book matched unless another match is specified
B Tight knots up to 1 in A few small knots up to 3/8 in (birch, maple, poplar)
C Open knotholes up to 1 in allowed No open defects; knots and repairs up to 1/2 in
D Open knotholes up to 2-1/2 in allowed No open defects; repaired up to 3/4 in, sound knots up to 1 in

So a "C" on a birch panel is a better-looking surface than a "C" on a sheathing panel, and an "A" on a sheathing panel is not the same promise as an "A" on hardwood plywood.

Which plywood grade does a small project need?

Stacked sheet goods and timber in storage
A small project rarely needs the top grade on both faces.

These are our recommendations based on the limits above, for typical small indoor builds:

Project or part Grade that fits Why
Painted shelf, painted cabinet side PS 1 A face (A-C or A-D) or HP-1 C/D face Paint hides patches and small sound knots; avoid open holes
Stained or clear-finished visible face HP-1 A or B face Only these limit knots and require matching; PS 1 A may show patches
Back panel or drawer bottom you will not see HP-1 back 3 or 4, or PS 1 C or D side facing in Appearance does not matter; open holes stay hidden
Both sides visible (a divider, an open shelf) HP-1 with a 1 or 2 back Backs 1 and 2 have all openings repaired
Shop jig, sawhorse top, cutting platform PS 1 C or D Cheapest; holes do not matter

Whatever grade you pick, check the actual sheet. The standards set maximums: a sheet can be better than its grade, but it is not supposed to be worse. Look at both faces under the store lights and count patches and holes on the side you will see.

Buying less than a full sheet

A full 4 by 8 sheet is the size the standards grade, and it is also the hardest thing to bring into a small apartment. Some stores sell smaller project panels (Home Depot has listed 2 by 4 foot poplar plywood project panels, for example), and store cutting services can break a sheet down so it fits in a car; ask at your store. Check any panel's label for the same grade information. If you do bring home a full sheet, our guide to cutting a plywood sheet alone covers supporting it safely without a helper, and cutting plywood without splintering protects the face you paid extra for. A bookshelf for a small space is a good first plywood project because it shows you exactly which faces need the better grade.

FAQ

What is the best plywood grade for furniture?

For a clear or stained finish, hardwood plywood with an HP-1 A or B face. For painted furniture, a PS 1 A face or an HP-1 C or D face is usually enough, as long as the face has no open holes.

Is A-C plywood good enough for a bookshelf?

For a painted bookshelf, yes: PS 1 Grade A is described as suitable for painting. The C side has open knotholes up to about 1 inch, so keep it facing the wall or inside the case.

What do the numbers in A-1 or B-2 plywood mean?

They are HP-1 back grades. A 1 back is the cleanest, with only small sound knots and tiny repairs. A 4 back can have knotholes up to 4 inches and is meant for hidden surfaces.

Is CDX plywood waterproof?

"CDX" is a trade name, not a PS 1 grade. Under PS 1, a panel with a D veneer cannot be classified Exterior, so a C-D panel is Exposure 1: meant for panels not permanently exposed to the weather. Read the bond classification on the stamp.

Does a higher plywood grade mean a stronger panel?

The veneer grades in both standards describe the surface and its defects. Structural performance in PS 1 is covered by separate marks such as span rating and Performance Category, so do not choose a face grade for strength.

One useful email at a time

Make more with the space you have.

Beginner projects, tool guidance, and practical workshop ideas.