Practical woodworking for apartments, rentals, and small spaces. About
Hand Tools

Best Wood for Beginners Using Hand Tools

Hard maple takes about 3.8 times the force to dent as eastern white pine. The best wood for beginners with hand tools, ranked with US Forest Service data.

Woodworking hand tools laid out on a workbench
By hand, a forgiving wood matters more than a fashionable one.
This article may contain affiliate links. We may earn a commission at no extra cost to you.

Short answer: the best wood for beginners (hand tools only) is soft wood with an even texture: eastern white pine, spruce, true fir and yellow-poplar, plus sugar pine, which is just as soft, are the easiest to saw, chisel and plane. Cherry, soft maple and black walnut are a sensible next step when you want furniture-grade wood. Oak, ash, hard maple and hickory are much harder to work by hand. One trap: southern yellow pine and Douglas-fir are softwoods, yet they are about 1.8 to 2.3 times as hard as eastern white pine in the Handbook's data and have hard and soft bands in every growth ring.

Most guides on this question share woodworkers' favorites, and those favorites are usually right. What follows shows why, using hardness, density, texture and shrinkage data from the US Forest Service's Wood Handbook, so you can judge a species that is not on anyone's list.

What makes a wood "forgiving" by hand?

Three properties do most of the work when you push a saw, chisel or plane through wood:

  1. Hardness. How much force the wood resists. The Wood Handbook's side hardness figure is the load needed to press a 0.444-inch steel ball halfway into the wood (a modified Janka test, Chapter 5). Softer wood generally takes less effort to cut (our inference; the test itself measures denting), and it also dents more easily.
  2. Texture within each growth ring. Some woods change sharply from soft earlywood to hard latewood inside each ring; others change gradually or hardly at all. Chapter 3 sorts species by exactly this. An even texture means a tool meets roughly the same resistance all the way across the board.
  3. Movement. How much the wood shrinks and swells with humidity. Less movement means fewer surprises after you cut a joint (Chapter 4, Table 4-3).

The best wood for beginners (hand tools): the numbers

Lumber boards stacked flat for storage
Hardness and grain decide how much effort each cut and plane stroke takes.

We pulled side hardness and specific gravity (both at 12% moisture, Table 5-3b), tangential shrinkage (Table 4-3) and the texture description from Chapter 3 for species a beginner is likely to meet. The "compared with eastern white pine" column is our arithmetic. Values are averages for clear, straight-grained test pieces, so a real board with knots or wild grain will behave worse.

Species Side hardness (lbf) Compared with eastern white pine Specific gravity Tangential shrinkage Texture (Wood Handbook, Ch. 3)
Western redcedar 350 0.9x 0.32 5.0% gradual earlywood-to-latewood transition
Eastern white pine 380 1.0x 0.35 6.1% much more earlywood than latewood
Sugar pine 380 1.0x 0.36 5.6% not described
Engelmann spruce 390 1.0x 0.35 7.1% gradual transition (spruces)
Basswood 410 1.1x 0.37 9.3% not described
Ponderosa pine 460 1.2x 0.40 6.2% not described
White fir 480 1.3x 0.39 7.0% gradual transition (true firs)
Yellow-poplar 540 1.4x 0.42 8.2% diffuse-porous
Red alder 590 1.6x 0.41 7.3% not described
Loblolly pine (southern yellow pine) 690 1.8x 0.51 7.4% abrupt transition
Douglas-fir (Coast) 710 1.9x 0.48 7.6% abrupt transition
Longleaf pine (southern yellow pine) 870 2.3x 0.59 7.5% abrupt transition
Black cherry 950 2.5x 0.50 7.1% not described
Red maple (a soft maple) 950 2.5x 0.54 8.2% diffuse-porous
Black walnut 1,010 2.7x 0.55 7.8% semi-ring-porous
Northern red oak 1,290 3.4x 0.63 8.6% ring-porous
White ash 1,320 3.5x 0.60 7.8% ring-porous
Sugar maple (hard maple) 1,450 3.8x 0.63 9.9% diffuse-porous
Shagbark hickory 1,880 4.9x 0.72 10.5% ring-porous

"Not described" means the Chapter 3 text we read does not classify that species' texture; it is not a claim either way.

Tier 1: the most forgiving woods to learn on

Eastern white pine, sugar pine, Engelmann spruce, white fir and yellow-poplar combine low hardness with even texture (the Chapter 3 text we read does not describe sugar pine's). The Handbook describes the spruces and true firs as having growth rings with "a gradual transition" from earlywood to latewood, names yellow-poplar among its "examples of diffuse porous species," and says eastern white pine has much more earlywood than latewood, which is why its density is low. In practice that means your saw and chisel meet steady resistance instead of alternating soft and hard bands.

Yellow-poplar is the hardest of this group at 540 lbf, about 1.4 times eastern white pine, but still well under half of hard maple. That extra firmness means it dents less than pine while staying easy to cut.

The trade-off with the softest woods is denting and crushing. Pine at 380 lbf takes about a quarter of the force that hard maple needs to make the same dent in the Handbook's test. A dull edge tends to crush soft fibers instead of slicing them, so if pine end grain looks ragged after a cut, sharpen before blaming the wood; our beginner sharpening guide covers the basics.

Basswood (410 lbf) is about as soft as white pine, but note its tangential shrinkage of 9.3%, one of the highest in the table. It suits small parts and practice pieces better than wide panels that need to stay flat.

Tier 2: a step up for furniture you want to keep

Black cherry, red maple (soft maple), black walnut and red alder sit between about 590 and 1,010 lbf: roughly 1.6 to 2.7 times eastern white pine. They need sharper tools and a little more effort, and in return they dent far less than pine. Black walnut is "a temperate-zone semi-ring-porous wood" in the Handbook's words, so its texture sits between the even maples and the strongly banded oaks. If your first box or shelf in pine went well, one of these is the natural second wood.

Tier 3: hard work by hand

Northern red oak, white ash, hard maple and hickory start at about 3.4 times the hardness of eastern white pine and reach almost 5 times for shagbark hickory. Oak and ash are ring-porous: Chapter 3 describes ring-porous woods as having large earlywood vessels and then "denser, more fibrous tissue in the latewood," and names northern red oak, white ash and shagbark hickory as examples. Hard maple is diffuse-porous, so its pores are even, but it is very dense. None of these is off limits, but they are tiring for a first project done entirely with a handsaw and chisel, and every mistake costs more effort to fix.

The softwood trap: southern yellow pine and Douglas-fir

Pine branch with needles, a softwood tree
Not every softwood is easy by hand; some pines are hard and resinous.

"Softwood" is a botanical group, not a promise that the wood is soft. In the table, longleaf pine (870 lbf) is harder than red alder and over 1.5 times as hard as yellow-poplar, a hardwood. Loblolly pine and Douglas-fir are nearly twice as hard as eastern white pine.

Texture makes it trickier. The Handbook lists southern yellow pine and Douglas-fir among woods with "an abrupt transition from earlywood to latewood." Our reading of what that means at the bench: a chisel or plane crosses soft earlywood and hard latewood bands in quick succession, so the tool tends to dig into the soft band and skip over the hard one. That is why these woods often feel less predictable by hand than their hardness number alone suggests. Both are sold as construction lumber, so if you practice on a 2x4, check the grade stamp for the species and expect it to behave differently from a clear white pine board.

How to choose your first wood

  • For practice cuts and joints: eastern white pine or another Tier 1 softwood. It is soft and even, and mistakes are cheap.
  • For a first painted project: yellow-poplar or pine. Poplar dents less; pine is softer to cut.
  • For a first natural-finish project you want to keep: cherry, soft maple or walnut, once you can keep an edge sharp.
  • Avoid as a first wood by hand: hickory, hard maple, oak and ash; and do not assume a construction 2x4 is "soft" because it is pine or fir.

Pair the wood with the right tools: our hand tool starter kit, Japanese pull saw guide and hand plane buying guide cover the tools that do this work. A small wooden box in pine or poplar is a good first test of all three.

FAQ

What is the easiest wood to cut with a hand saw?

Among the species in the Wood Handbook data we compared, western redcedar, eastern white pine, sugar pine and Engelmann spruce are the softest, at about 350 to 390 lbf of side hardness, and western redcedar and the spruces have a gradual ring transition, per the Handbook.

Is poplar good for beginners?

Yes. Yellow-poplar is a diffuse-porous hardwood with a side hardness of 540 lbf, about 1.4 times eastern white pine, so it is easy to cut but dents less than pine.

Is pine too soft for furniture?

Not for furniture, but it dents easily: eastern white pine needs about a quarter of the force that hard maple does to make the same dent in the Handbook's test. For tabletops that take daily knocks, a harder wood like cherry or maple holds up better.

Why is oak hard to work with hand tools?

Northern red oak is about 3.4 times as hard as eastern white pine in the Handbook's data, and it is ring-porous, with large open earlywood pores and dense latewood in every ring. Both make it slower going with a saw and chisel.

Should beginners practice on construction 2x4s?

They are cheap for practice, but check the species on the stamp. If it is southern yellow pine or Douglas-fir, the wood is about 1.8 to 2.3 times as hard as eastern white pine and has an abrupt hard-soft ring pattern, so practice results on a clear white pine or poplar board will be more consistent.

One useful email at a time

Make more with the space you have.

Beginner projects, tool guidance, and practical workshop ideas.